This floor was another case of builders failing to protect the Quarry Tiled Floor when they were working at this house in Bedford, this is certainly not un-typical of plasters considering the number of messy floors we have had to clean up previously. I guess in some ways we shouldn’t complain as they are keeping us busy but it was my floor I would be quite upset.
Deep Cleaning Quarry Tiles
To get rid of the plaster I applied a solution of Tile Doctor Grout Clean-up which is an acid based product designed to remove grout from the surface of tiles but works equally well on cement, plaster and other mineral deposits such as effloresce and rust. Working in sections the Grout Clean-up was applied, scrubbed in and then washed off, being an acid it’s not advised to leave it on the tile for too long.
Once the plaster was dealt with the whole floor including the tiles and grout was given a good clean using Tile Doctor Pro-Clean which is a strong alkaline product that’s safe to use on Tile, Stone and Grout. For best results leave it to soak into the tile for twenty minutes before giving the tiles a good scrub.
Once the tiles were clean the floor was given a good rinse with clean water to remove any remaining chemical and neutralise the floor before sealing; a wet vacuum was used to remove as much water from the floor as possible so it could dry faster.
Sealing Quarry Tiles
We left the floor to dry overnight and came back the next day to seal it using four coats of Tile Doctor Seal and Go sealer which adds a nice sheen to the floor as well as providing long term stain protection. The photographs above show the transformation of the floor and certainly the customer was very happy with the result.
Removing Plaster from Quarry Tiles in Bedfordshire
This was a very straightforward request to clean and seal an old Quarry tiled floor that dated back to the Victorian era. The tiles didn’t appear to have any sealer or other treatment applied, it could be if there was anything it had worn off a long time before.
Cleaning Old Quarry Tiles
A strong dilution of Tile Doctor Pro-Clean was applied to the floor and left to soak into the tile for around twenty minutes before being worked into the floor using a rotary floor scrubber fitted with a black pad. Pro-Clean is a strong alkaline product so unlike acid based cleaners it’s safe to use on any tile and stone which given the age of these tiles was quite an important consideration.
Pro-Clean was also used along the grout lines which were scrubbed by hand using a stiff brush. The floor was then rinsed with clean water which was removed using a wet vacuum and the whole process repeated until we were happy that the tile and grout was clean.
This process took most of the day and before we left the floor was given a thorough rinse with clean water to remove any trace of Pro-Clean as this can upset sealing later on.
Sealing Quarry Tiles
The floor was left to dry overnight and when we came back the next day we were able to start the sealing process. For sealing a combination of sealers was used starting with a single coat of Tile Doctor Colour Grow; Colour Grow is a impregnating sealer that fills the pores in the tile in order to repel any contaminates that can stain the floor, it also as its name suggests brings out the colour in the tile. Once this had dried a coat of Tile Doctor Seal and Go was applied which is a topical sealer that adds a nice sheen to the floor. This proved to be a great combination and the quarry tiles looked really nice when they were finished in fact the customer was so surprised by the result we had managed to achieve.
Cleaning old Victorian Quarry Tiles in Bedford
We were asked to work our magic on these dirty Quarry tiles at a residence in the historic town of Hitchin. The tiles had been sealed on a number of occasions but had not been deep cleaned beforehand which effectively trapped the dirt under the sealer making it difficult to get clean.
Stripping Quarry Tiles
To get them clean the coatings on the surface of the Quarry tile had to be stripped off back to the original surface. To do this we mixed a dilution of Tile Doctor Remove and Go 50/50 with NanoTech UltraClean and applied it to the floor leaving it to soak in to the tile for around 20 minutes before scrubbing it in with a wire brush. Remove and Go is as its name suggests is a coatings remover which is safe to use on Tile and Stone and is designed to remove most products from, this is assisted by the addition of NanoTech UltraClean which adds tiny abrasive particles into the solution making it more effective. The floor was then scrubbed using a rotary machine fitted with a black scrubbing pad and the grout lines scrubbed by hand using a stiff brush. The floor was then rinsed with water which was removed using a wet vacuum. The process was then repeated until we were happy that the tile and grout was clean and that the old sealer had been removed, again the floor down and being the last time washed down thoroughly as traces of cleaning products can upset sealers later on.
Sealing Quarry Tiles
Once happy with the floor and it had time to dry off it was sealed with four coats of Tile Doctor Seal and Go sealer adds a nice sheen to the floor as well as adding long term stain protection; needless to say the customer was very happy with the results.
Resolving Quarry Tile Cleaning problems in Hitchin